Adding cutting tools efficiency

06-01-20 Cutting tools efficiency

Its not easy to determine/ predict how long should a cutting tool last, but its life span is based of known factors;

These factors include cutting tool geometries, coatings, sizes, brands, surface footage, depth of cut, width of cut, feed per tooth, dry or wet machining, horsepower consumption, and rigidity (and also Machine tool type, software, surface geometry, raw material to cut). Manipulating these variables can lead to vastly different outcomes, so a shop’s approach to machining costs is key.   

For example, many shops only look at price when selecting their cutting tools and toolholders. This narrow view often results in very poor machine efficiency, which can lead to substantial hidden costs, including longer cycle times, poor tool life, inaccurate profile tolerances and so on. The average mold shop can spend between 2 and 4 percent of its total operating costs on cutting tools and toolholders. If a shop were to find a tool that is half the cost of the one it is currently using, it could theoretically reduce tooling expenses to 1 to 2 percent of operating costs. However, a more expensive tool that can get parts out of the machine twice as fast would double the shop’s potential revenue. Which scenario would you prefer? The answer to this question can be difficult in real-world machining environments, and most shops’ situations fall somewhere in between the two extremes. 

Adding Value

Consider these three performance values of the cutting tool to determine machining costs and identify the appropriate machining solution for a shop:

1. The time required for the cutting tool to get parts through the machine.

2. Cutting tool life, as defined by either the number of cutting tools per part or the number of parts per cutting tool. 

3. Cost of the cutting tool used. 

As you can see, the actual cost of a cutting tool is only one of three factors in the equation, so if that is the only value taken into account, the shop is ignoring the two other essential considerations. To maximize productivity, a shop needs to get parts off the machine as fast as possible at the lowest cutting tool cost with the best possible cutting tool life. 

Comparing these key considerations against each other in real-life applications requires some basic math (see chart below). For example, the cost of cutting tool per part plus the shop rate divided by the number of parts per hour. The cost of the cutting tool per part is typically a very small part of the total cost of production. Although using a much less expensive tool initially looks very attractive for reducing part costs, very often that cost savings is only a small part of the total cost reduction. The larger cost savings for most shops comes from getting parts off of the machine more quickly.

Finding Balance

Increasing output often involves running the cutting tools faster. In milling metals, higher surface footage results in the cutting tool running hotter, which can improve a material’s machinability, as the material flows more easily away from the parent material and across the tool. However, this extra heat will also lower cutting tool life, as it breaks down the hot-hardness of the cutting tool. This often results in thermal cracking or cutting tool deformation. The goal is to find a balance between running longer and running faster. 

This balance typically comes down to the application at hand and the preferences of the shop, meaning the shop applies speeds and feeds that achieve a certain number of minutes in the cut, depending on its machining philosophy. For example, does the shop want minimal cycle time and maximum output, or does it emphasize consistency and unmanned machining, sacrificing machining speed for reliability and longer tool life? More specifically, some shops target roughing tool endurance of 15 minutes. If the tool lasts longer, they increase the speeds and feeds until that endurance falls to the 15-minute range. The philosophy here is to get the parts out of the machine as fast as possible. These shops consider cutting tooling costs to be insignificant compared to shop costs such as labor and machine tool time. 

Other shops prefer their cutting tools to be as reliable as possible, offering consistency in performance. This is because their machinists are responsible for more than just running one machine or they have a more conservative mindset when it comes to running the shop. Their tools, therefore, run at parameters that allow unmanned operation and the longest tool life possible. This approach is commonly utilized with a lean staff and/or night-time runs. These shops are more likely to target 30 to 60 minutes of tool life, adjusting the speeds and feeds accordingly to achieve this result consistently. Still others believe that aggressive machining is hard on the machine tool and so prefer to maximize machine spindle life.

Adjusting Cutter Costs

Advances in cutter technology, such as indexable tooling, which has become a popular choice for mold roughing, also impact machining costs. With the indexability of cutting tools comes costs associated with each insert rotation that must be considered. A shop cannot simply calculate the cost per cutting tool. 

In addition to the cost of the inserts and how long they will last, it is important to consider the number of edges on each insert and the number of inserts in the cutting tool. A cutting tool that offers four usable edges offers an economic advantage in terms of cost per available edge over a tool that offers only two usable edges, depending on the performance capabilities of the cutting tools. Similarly, a tool with four flutes that can achieve the same metal-removal rate (MRR) and tool life as a tool with six flutes also offers an economic advantage. This is sometimes referred to as cost per rotation, and can be calculated using the following formula: number of inserts in the tool multiplied by insert cost divided by number of usable edges on the insert.

There are many variables to consider when it comes to cutting tool and machining costs, so it is worth taking the time to conduct the in-depth analysis required to determine the proper machining approach and the most appropriate cutting tool for each application.

At the end, one should find a balanced solution accordingly its own working context (it can even be concluded that the amount spent in cutting asa variable is almost expendable/ no owth to be taken into account) ; ideally inf you are into it, register as many data as possible in order to build a reasonable data set, that can predict at least the most commonly tasks done otherwise it can be an endless well.

 

Read more here

Source MMT

 

Keywords: #cuttingtools #efficiency #toolmanagers #shapes #molds #moulds #moldsfromportugal #moulds4_0 #industry4_0

Barreiros uses cookies to offer a better online experience. The use of our services presupposes an acceptance of our cookies policy More Informations

OK